| 
|
Hottt!!!
That's what we say about our bodywork. We've got more GSXR 1000
fairings than you can shake a stick at! Whether you're looking
for a race or street fairing, race tail, undertail or stock replacement
lowers, Airtech's got what you need! |
 |
 7GSXR7SS1
Suzuki GSXR 1000 Supersport race upper fairing
What we have here is the upper fairing to our two-piece race fairing
assembly. This piece is the upper headlight area with the headlight
holes filled in and half of the right and left lowers and the
radiator shroud all molded as a one-piece unit. This fairing splits
with the upper and lower down about the base gasket of the cylinder
of the bike down halfway threw the side. This allows you to remove
the fairing assemblies on and off the bike very quickly and easily
also allowing a smooth clean design because you don't any parting
seams up by the handlebars or around all of the radiator shrouding.
This piece only works with our 7GSXR7SS2 lower.
Please note: This is a GSXR750 part that
will work on your GSXR1000. You'll have to fabricate a small bracket
out of flat strap from the rear cylinder head mount to the mounting
hole on the fairing, just behind the large vent. The hole is about
an 1" forward compared to the GSXR1000.
Price |
 |
 7GSXR7SS2
Suzuki GSXR 1000 Supersport race lower fairing
This is the bottom half to our two-piece super sport race fairing
assembly. This piece is the bottom right and left lowers, the
front radiator shrouding, and the oil containment belly pan all
molded as a one-piece unit. This fairing is cut open on the left
hand side for your generators and does have a side stand provision.
This piece only works with our 7GSXR7SS1 upper fairing.
Please note: This is a
GSXR750 part that will work on your GSXR1000. You'll have to trim
the lower slightly in the rear to clear the oil cooler on the
GSXR1000.
Price |
| 
|
 7GSXR12
Suzuki GSXR 1000 Right lower fairing
Lightweight replacement fairing for your damaged right lower.
Drill the mounting holes and attach it to all of your stock brackets
and use all of your stock hardware. A little fabrication is required
down at the lower oil cooler guard behind the front tire. A crafty
guy can do that in a few minuets or simply leave that radiator
guard off. Save yourself a ton of money over the stock. Factory
Suzuki pieces. Get yours today!
Price |
| 
|
 7GSXR13
Suzuki GSXR 1000 Left lower fairing
Lightweight replacement fairing for your damaged left lower. Drill
the mounting holes and attach it to all of your stock brackets
and use all of your stock hardware. A little fabrication is required
down at the lower oil cooler guard behind the front tire. A crafty
guy can do that in a few minuets or simply leave that radiator
guard off. Save yourself a ton of money over the stock. Factory
Suzuki pieces. Get yours today!
Price |
| 
|
 7GSXR71C
Suzuki GSXR 1000 Competition upper fairing
This is a great little upper fairing for custom street applications
or track day bikes. Track day guys love this fairing because they
can take there expensive stock headlight assembly off of there
bike, paint our upper fairing put it on there bike and go. Custom
street bike guys love this because they can cut different headlight
shapes in front of the fairing to butt up against there stock
headlights. We've seen people cut round headlights, cat's eyes,
even a smiley face cut our of the front of the fairing and had
the headlight shining threw in the back. This is a cool piece
for your GSXR1000.
Price |
| 
|
7GSXR71S
Suzuki GSXR 1000 Street upper fairing
Replace your crash damaged street fairing with one of our lightweight
fiberglass pieces. Simply replace all of your bent, busted brackets,
drill out mounting holes out of our fiberglass fairing, and mount
on your bike and go riding again. Please note that we do not do
the tab work on the inside of our fairing for the headlights simply
because the headlight is mounted into the metal fairing bracket,
the fairing bracket supports the weight of the heavy headlight
assembly. Although the headlight was retained in the fairing originally
from Suzuki it is not necessary to hold the headlight onto the
bike. Simply mount your headlight into your bracket, put the fairing
assembly up on your bike, mount the fairing at the mirrors on
the top, and mount the fairing on both sides at the lowers on
the bottom and go riding. This method holds up great at over a
hundred miles per hour. If you have any questions about the headlight
mounting assembly call one of our sales reps or our tech guy today.
Price |
| 
|
 7GSXR74B
Suzuki GSXR 1000 Superbike tail
What we have here is one of our one-piece race tails. We've taken
the right and left seat sides, the solo seat cowl area, and the
tail light area and molded it into a one-piece unit. We call this
tail light super bike tail because the seat pan area where the
rider sits is filled in and flat and uses close cell race padding
instead of the stock upholstery. This is a race legal tail section
for most racing organizations and is a cool tail section for custom
street bikes. Get one today!
We offer a bracket assembly (7GSXR74SB,
shown below) to support the riders weight so the fiberglass tail
section doesn't break.
Price |
| 
|
 7GSXR74SB
Suzuki GSXR 1000 Seat Bracket
Use this seat bracket to support the riders weight when using
our 7GSXR74B Super bike race tail. You will need to drill some
mounting holes near subsection to mount this bracket. We've seen
people put rib nuts in the frame, use self-tapping screws, and
some people will even popper this into the frame. This is a quick
and easy installation.
Price
|
| 
|
 7GSXR74S
Suzuki GSXR 1000 Supersport tail
Our most popular race tail for the GSXR 1000. This tail is right
and left seat sides, the solo seat cowl, and tail light area all
molded as a one-piece unit. The seat pan area, where the rider
sits, is open to use with the stock Suzuki upholstery. This is
an easy instillation, drill four mounting holes and mount onto
your chassis. This is a race legal tail section for most racing
organizations and is also a cool custom street bike tail section,
the taillight is easily cut open for street use. Get yours today!
Price |
| 
|
7GSXR74S4
Suzuki GSXR 1000 Dragbike tail +4
Stretched+4, this tail section is like our 7GSXR74S but only four
inches longer. Use your stock upholstery or our stepped drag bike
seat pan 7GSXR77 below.
Price
|
| 
|
7GSXR74S6
Suzuki GSXR 1000 Dragbike tail +6
Stretched+6: same tail as our 7GSXR74S but stretched six inches
longer than stock. Use your stock upholstery or our stepped drag
bike seat pan 7GSXR77 below.
Price
|
| 
|
7GSXR74BB
Suzuki GSXR 1000 Battery box
Small battery box that will fit between the subframe rails on
a custom race bike where the stock battery box and all teh attached
crap has been removed. Perfect for use witha modern lithium ion
battery.
Please
note: bottom side up in the picture, in case you were
wondering...
Price
|
| 
|
7GSXR77
Suzuki GSXR 1000 Dragbike Seat pan - stepped
This stepped dragbike seat pan fits any of our supersport tail
sections above, or can be used with your stock tail section. Puts
you down lower in the seat pocket for better launching.
Price
|
| 
|
 7GSXR75
Suzuki GSXR 1000 Front fender
Direct replacement for the GSXR front fender. Just drill the mounting
holes, take off your heavy plastic piece, and install our lightweight
fiberglass fender. This fender is lighter than stock so your suspension
reacts faster. This fiberglass fender is also available in carbon
fiber. Ask one of our sales reps today.
Price
|
| 
|
 7GSXR79
Suzuki GSXR 1000 Undertail - under seat enclosure street
Hack out all that ugly plastic crap underneath your tail section
and install one of our cool fiberglass under seat enclosures.
This piece uses your stock DOT approved tail light assembly so
you don't have to worry about someone rear ending you like happens
with guys using undertails with dim LED lights. Those pieces are
pretty unsafe, ours uses the stock DOT taillight.
Our piece also has a license plate bracket molded into it so you
don't have to fabricate or bend any pieces of metal like our competitors
under seat enclosures. Simply hack out your black plastic pieces,
do a little bit of cutting and trimming, and custom paint this
under seat enclosure for an awesome custom street bike.
Price |
| 
|
7GSXR79R
Suzuki GSXR 1000 Undertail - under seat enclosure race
Remove all that heavy black plastic under seat rear fender assembly
and lighten up the back of your race bike. This race piece attaches
inside of our super sport or super bike race tail and cleans off
the inside bottom of your race bike. This is a must have to finish
off the underside of your race bike.
Price
|
| 
|
 7GSXR711
Suzuki GSXR 1000 Fuel Tank
Here is a lightweight racing fuel tank for your GSXR. Yes, we
mean lightweight. It's a tremendous weight saving off the top
of your motorcycle. Your bike will handle a lot better, it will
flick from right to left hand sides and turn into corners a lot
faster without the extra weight on top of your motorcycle.
This race tank is identical in
dimensions to the stock fuel tank. The fuel tank mounts to your
stock rear-mounting bracket. It comes with a lightweight racing
gas cap and has an aluminum flange in the bottom of the tank to
use with your stock fuel pump. You can also add additional bungs
in the bottom for nitrous or turbo systems. Just ask our sales
reps for details. Tank comes with internal venting system. Save
a ton of weight off of your bike and be able to increase the handling
in your motorcycle by getting one of these fuel tanks today!
Price
Please note! This gas tank
is not recommended for street use, this is a fiberglass gas tank
that will not dent. In the event of a crash, the gas tank
may rupture and spill fuel possibly catching your motorcycle on
fire. This gas tank is recommended for racing purposes, with racing
fuel only! Read more...
|
| 
|
7GSXR711S
Suzuki GSXR 1000 Slammed fuel tank
This is an awesome racing gas tank for your GSXR. Not only is
this gas tank lighter than your stock fuel tank but this gas tank
is slammed and smaller. What we mean by that is that this gas
tank is two inches lower in the rear, that part that digs into
your stomach, it is two inches lower in the back and the gas tank
is actually two inches narrower so you can hold onto the bike
at your crotch better and your elbows aren't restricted when you're
hanging off the side of the motorcycle. Drag racers love this
gas tank because it allows them to slide forward and stay over
the top of the tank. Road racers love this tank because it allows
them to move around the motorcycle more freely than the stock
fuel tank does. You will love this gas tank.
The gas tank has aluminum mounting
plate in the back to use with your stock mounting brackets and
has an aluminum flange to fit your stock fuel pump. It comes with
a nice aluminum racing gas cap. Tank has internal venting. Other
options include carbon fiber or additional bungs for nitrous or
turbo. Whether you are drag racing or road racing your GSXR you
need this gas tank. Purchase yours today!
Please note! This gas tank is not recommended for street
use, this is a fiberglass gas tank that will not dent. In
the event of a crash, the gas tank may rupture and spill fuel
possibly catching your motorcycle on fire. This gas tank is recommended
for racing purposes, with racing fuel only! Read
more...
Price |
| 
|
7GSXR710D1
Suzuki GSXR 1000 Competition Air Duct
This is a very popular piece with track day riders because they
can take off there stock upper fairing and headlight assembly
and save there expensive pieces in case of a crash. These airducts replace the factory units. Get yours today!
More
photos
Price
|
 |
 GL30A
Suzuki GSXR 1000 Grey line fairing set This fairing
set is extremely popular with our racers and also with the custom
street guys because they can save themselves a lot of money.
This four-piece set is everything you need for a paint set on
your race bike or custom street bike. This set includes our
super sport race upper fairing, super sport race lower fairing
with oil containment, and this kit only comes with our super
sport race tail section as well as a front fender.
All you need to do
to run this kit on the street is cut out head- and taillight
openings. With a little bit of fabrication skill you can save
yourself a grip of money!
Price
|
